(888) ipd-converters (888) 473-2668 www.ipdconverters.com c-68 55 60 65 70 75 80 85 90 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. iwd1209 eff. iwd1212 50 55 60 65 70 75 80 85 90 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. iwd505 eff. iwd512 technical specifications general description features efficiency vs. load (12v input) efficiency vs. load (5v input) iwd series - dual output, 10 watt notes 1 converter will auto-restart once fault has been removed. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. iwd dual output dc/dc converters offer excellent regulation and isolation in an industry standard package. available in 5v and 12v input versions, the iwd is perfect for industrial, datacom, or telecom applications. the iwd features short circuit protection and 500 vdc isolation. please see the iws and ias series for single output applications. industry standard package industry standard pinout 85c case operation short circuit protection 5v and 12v inputs input pi filter 6-sided shielding wide input voltage 500v isolation switching frequency 300 khz isolation input - output 500 vdc isolation resistance - input to output 10 9 ohms standard case operating range -25 to +85c industrial range (add -i to p/n) -40 to +85c storage range -40 to + 125c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 5 g, 10 - 55 hz safety ul, cul, tuv weight (approx.) 1.4 oz setpoint accuracy 1% line regulation v in min. - v in max., i out rated 1.0% v out load regulation i out min. - i out max., v in nom. 1.0% v out minimum output current 10 % i out rated dynamic regulation, loadstep 25% i out pk deviation 1% v out settling time 500 s temperature coefficient 0.02%/c ripple and noise, 20 mhz bw 1% v out nom. short circuit protection 1 hiccup current limit 130% output input voltage range 5 vdc nominal 4.5 - 9 vdc 12 vdc nominal 9 - 18 vdc reflected ripple 20% i in max. reverse input current 100% i in max.
c-69 thermal impedance natural convection 15.4 c/w 100 lfm 12.2 c/w 200 lfm 9.3 c/w 300 lfm 7.4 c/w 400 lfm 6.4 c/w note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. iwd series - dual output, 10 watt mechanical drawing pin function 1+v in 2-v in 3+ v out 4 common 5- v out tolerances inches: (millimeters) .xx 0.040 .x 1.0 .xxx .010 .xx 0.25 pin: 0.002 0.05 case: + 0.04, - 0.00 + 1.0, - 0.0 (tolerances as listed unless otherwise specified.) models - (see the last page of this file for options.) vin (volts) vin range (volts) iin max.* (amps) vout (volts) iout rated (amps) ripple & noise pk-pk (mv) efficiency typ. ** model 5 5 5 12 12 12 4.65 - 5.50 4.65 - 5.50 4.65 - 5.50 10.90 - 13.20 10.90 - 13.20 10.90 - 13.20 3.20 3.20 3.20 1.55 1.55 1.55 5 12 15 5 12 15 1.000 0.500 0.375 1.000 0.500 0.375 50 120 150 50 120 150 82% 80% 82% 80% 84% 82% iwd505 iwd512 iwd515 iwd1205 iwd1212 iwd1215 * maximum input current at minimum input voltage, maximum rated output power. ** at nominal vin, rated output. 1.40"(35.6mm) bottom view 0.800"(20.3mm) 0 (4.6mm) 0.18" min. (1.0mm) dia 0.040" (10.2mm) 0.40" (50.8mm) 2.00" (25.4mm) 1.00" 4 2 53 1 (-2.5mm) -0.10" 0 (20.3mm) 0.800" (7.6mm) 0.300" (10.2mm) 0.400" (12.7mm) 0.500"
c105 options when ordering equipment options, use the following suffix information. select the option(s) that you prefer and add them to the model number. example ordering options are located below the options table. option suffix applicable series remarks negative logic n has, hbd, hbs, hes, les, qbs, qes, tes, tqd ttl ?low? turns module on ttl ?high? turns module off lucent compatible trim t has, hbd, hbs, hes, qbs, qes t e r m i nal s t r i p t s x w s , xwd, xwt trim 1 ias, les enable 2 iad, ias, les, sms trim and enable 3 ias, les current share 4 sms headerless y encapsulated ews, iws, ows pin length and heatsink options standard pin length is 0.180? (4.6mm) 0.110? (2.8mm) pin length 8 all units (except sms) 0.150? (3.8mm) pin length 9 all units (except sms) 0.24? (6.1mm) horizontal heatsink 1h all units (except dip, sip, and sm packages) includes thermal pad 0.24? (6.1mm) vertical heatsink 1v all units (except dip, sip, and sm packages) includes thermal pad 0.45? (11.4mm) horizontal heatsink 2h all units (except dip, sip, and sm packages) includes thermal pad 0.45? (11.4mm) vertical heatsink 2v all units (except dip, sip, and sm packages) includes thermal pad 0.95? (24.1mm) horizontal heatsink 3h all units (except dip, sip, and sm packages) includes thermal pad 0.95? (24.1mm) vertical heatsink 3v all units (except dip, sip, and sm packages) includes thermal pad example options:hbs050zg-ant3v = hbs050zg-a with negative logic, lucent compatible trim, and 0.95? vertical heatsink. les015yj-3n = les015yj with optional trim and enable, negative logic. qbs066zg-at8 = qbs066zg-a with lucent compatible trim and 0.110? pin length. nuclear and medical applications power-one products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the president of power-one, inc. technical revisions the appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. specifications are subject to change without notice.
|
